AURIX™ Forum Discussions
Hi members,
I have a problem with SCR debugging.
it is exactly the same as SCR Debugging problem - Infineon Developer Community
I wrote my own SCR code for development and flashed it to AURIX with SCRCFG 0x0.
and changed SCRCFG 0x0 to 0x1 and then everything was good.
SCR worked what I wanted.
But when I changed SCRCFG 0xA and then started SCR, suddenly SCR start address was placed at "_Exit".
So if I want to run the SCR, I should change the address to 0x0.
How can I run the SCR with SCRCFG to 0xA and the start address at 0x0 without any modification about the start address?
Please Let me know.
Show Less
Dear Team,
I want to know the difference between DAP miniwiggler and XMC_LINK_SEGGER_V1.
Hi members,
I have a question about How can I erase SMU ALM7[7].
This Alarm is related to the SPU Module, However, in this IC, There is no SPU Module.
So I wonder why this alarm is activated and How can I erase this alarm.
Every time I turn on this IC, the alarm is set to 0x1.
And I tried to clear All the Alarm, but Alram 7[7] was always High.
please let me know that.
Thank you.
Show LessIm using tc377 for uart communication, I have to send data from tx without interrupt by using Timer(Gpt12)
when i using this Data is stored in Tx buffer but not transmitting to Rx.
This is timer function
void interruptGpt12_T3(void)
{
IfxCpu_disableInterrupts();
IfxPort_togglePin(LED);
if(g_flag1 == 1)
{
send_receive_ASCLIN_UART_message();
}
IfxGpt12_T3_setTimerValue(&MODULE_GPT120, RELOAD_VALUE_T3);
IfxCpu_enableInterrupts();
}
This one data transfer and receive function through uart
extern void send_receive_ASCLIN_UART_message(void)
{
IfxAsclin_Asc_write(&g_ascHandle, g_txData, &g_count, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &g_count, TIME_INFINITE); /* Receive data via RX */
}
Show Less
Hi, I can't add any printf or can't use UART from sample Ethernet application
if I add anything there it is crashing
I need to process data after receiving from Ethernet but if I try to do anything application just crash. So how and where to process Ethernet data.
Show LessHi, I am using Aurix TC375 Lite Kit development board and tried the freeRtos example code.
But after compilation, once the code is put in the debugger mode then the tsim issue comes as below snapshot --
Please get me a solution for this issue asap.
Thanks.
Show LessI am using Application Kit TC3X7 V2.0 TFT board
I have configured BMHD but the board all the time boots from Internal flash ignoring BMHD settings
If i want to use Alternate Boot Mode or BMI to boot , which all changes i need to do on the board?
Show LessThis Q&A just discussed P/D Flash, AURIX™ MCU: Error Correction Code (ECC) support - KBA238244
My question: is there special ECC for RAM and CAN relevant memory, e.g. Message RAM
Show LessHi there,
Can you confirm whether the statement below is true?
"Where a watchdog timeout alarm (CPU or safety) is triggered the microcontroller will always reset"
I am learning about recovery timers and so far through my observation this appears to be true. I find the wording in the manual ambiguous however, where the word "ensure" is used in reference to this.
Thanks
Show Less