AURIX™ Forum Discussions
Hello Community,
I am started using TC233 development board for few days and i ant now to display a hello wolrd or messga in the Console but i didn' found how to do i tried also to display it on the putty but also it doesn't work.
is there any code exmaple or something that can help me.
Thank you
Hi, I am using TC 387. Is it possible to do multi tasking in this board in a single core?
Hi I need to fetch data from ethernet module in ethernet_input function. But it crashes if I try to fetch anything.
ethernet_input(struct pbuf *p, struct netif *netif)
Is there any way to get data from there? I need to make some CAN packet using those.
Show Less
Hello Infineon Team,
I am using TC377_ED_EX AURIX Tricore microcontroller, I have integrated RTOS code with my general configurations, code was built successfully in Tricore IDE, however after flashing code in Lauterbach T32 debugger, and doing step over at every function and getting trap at __mtcr().
If code is in trap, then in some trap registers it should show status in trap registers, but in Trap registers also there is no specific value only 0000000 given.
for better understanding, I am attaching screenshots of call stack, error window, & registers value log
Hope you will provide me better solution to overcome this issue.
Thanks,
Poonam
Show Less
近日,我购买了一块KIT_AURIX_TC397_TFT板子,里面是官方默认的固件, 我看说明书里通过板子的Mini USB连接PC (Windows 10 ),就可以识别到板子,但是我用usb连接后,板子TFT屏幕正常点亮,只有D106 (V_UC)、D104 (SS2)灯亮和P13中的一颗灯在闪烁,但在PC设备管理器里面找不到Infineon JDS DAS COM和Infineon JDS DAS Debug,安装DAS软件也无法识别,这种情况应该怎么处理?
Show LessHi, I am using Aurix TC375 Lite Kit development board and tried the freeRtos example code.
But after compilation, once the code is put in the debugger mode then the tsim issue comes as below snapshot --
Please get me a solution for this issue asap.
Thanks.
Show LessHi, I can't add any printf or can't use UART from sample Ethernet application
if I add anything there it is crashing
I need to process data after receiving from Ethernet but if I try to do anything application just crash. So how and where to process Ethernet data.
Show LessNewbe here ( i have asked questions about other items i'm working on , CAN mainly ) i'm running through the examples with regards PWM generation and reading Analogue voltages.
I'm involved in a project where i will need to run a number of vales at 20khz but read the current coming back from the current sense circuit connected to them , in the end P.I. control over the current in the valve. I'm unsure which way to go .
I've tried looking at examples for CCU60 and then adapting the ADC examples in to it but nothing comes back off the ADC or i receive a trap error in debug - can i run ccu60 and get it to trigger ADC .
i've added
// Activate the line ServiceRequest_3 to route the CC60 Rising Edge to trigger EVADC module ....... ADDITION BY JOHN 🙂
IfxCcu6_enableInterrupt(&MODULE_CCU60, IfxCcu6_InterruptSource_cc60RisingEdge);
IfxCcu6_routeInterruptNode(&MODULE_CCU60, IfxCcu6_InterruptSource_cc60RisingEdge, IfxCcu6_ServiceRequest_3);
in the ccu6 init routine
plus i've ported in the ADC example code
/* Configure the EVADC module to trigger a conversion based on trigger from ccu6 ??? */
/* Trigger 0 is connected to CCU6 ServiceRequest_3 line */
adcGroupConfig.queueRequest[0].triggerConfig.triggerSource = IfxEvadc_TriggerSource_0;
/* Select the trigger event type */
adcGroupConfig.queueRequest[0].triggerConfig.triggerMode = IfxEvadc_TriggerMode_uponRisingEdge;
if i set breakpoint in the ADC ISR to check result nothing is read.
Am i wasting my time here as ccu6 can not produce PWM and give off trigger to ADC
thoughts any one ?
thanks