Not applicable
Aug 29, 2014
02:01 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 29, 2014
02:01 AM
I want to connect a XC2723X with Infineon Memtool through my DAP two wire interface (P2.9, P10.12). Looking at the user's manual there is no Hardware Pin configuration for DAP. I can find only JTAG Hardware configuration.
What pin configuration do I need to connect with DAP interface ?
Thanks in advance.
What pin configuration do I need to connect with DAP interface ?
Thanks in advance.
Labels
- Tags:
- IFX
3 Replies
Sep 03, 2014
04:54 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 03, 2014
04:54 AM
perhaps you can try following:
(installation of DAS Edition v4.0.5 and Memtool 4.05.04 or higher required)
• Start “DAS Server Control Panel”
• If “UDAS” is not listed as running DAS Server click “Installed Servers” and start “UDAS”
• Start “DAS Device Scanner”
• Attach board to PC via DAP with miniWiggler
• The board should be listed as “UART responding (DAS JDS miniWiggler JTAG/DAP/SPD V2)”
If the board is answering as listed above you can go in Memtool:
• Click “Target” >> “Change” >> “New”
• Select “Use a default target configuration” >> [your controller] >> “Easy Kits (Bootstrap Loader)” >> “Easy Kit with [your controller] (BSL/UART-over-SPD)”
• Close windows “Create or use default” with “Finish”-button and “Select Target Configuration” with “OK”-button
• Click “Connect”-button to establish connection to board
• Click “Setup …”-button and select page “Protection / BMI”
• Check “Install BMI configuration”, select “Two Pin DAP (DAP0=2.9, DAP1=P10.12)” in the dropdown box and close window with “OK”-button
• Click “HW Protect”-button and in the popup-windows “Start”-button afterwards. Be shure that no areas were selected for protectin before accepting the following message of IMT!
• After the process finished Memtool can be closed
In the “Das Device Scanner” the controller should be listed as “XE166/XC2000-Familiy” from now on and can be flashed via Memtool with Target Configration Profile for DAS
Hope this helps to get your Hardware connected?!
(installation of DAS Edition v4.0.5 and Memtool 4.05.04 or higher required)
• Start “DAS Server Control Panel”
• If “UDAS” is not listed as running DAS Server click “Installed Servers” and start “UDAS”
• Start “DAS Device Scanner”
• Attach board to PC via DAP with miniWiggler
• The board should be listed as “UART responding (DAS JDS miniWiggler JTAG/DAP/SPD V2)”
If the board is answering as listed above you can go in Memtool:
• Click “Target” >> “Change” >> “New”
• Select “Use a default target configuration” >> [your controller] >> “Easy Kits (Bootstrap Loader)” >> “Easy Kit with [your controller] (BSL/UART-over-SPD)”
• Close windows “Create or use default” with “Finish”-button and “Select Target Configuration” with “OK”-button
• Click “Connect”-button to establish connection to board
• Click “Setup …”-button and select page “Protection / BMI”
• Check “Install BMI configuration”, select “Two Pin DAP (DAP0=2.9, DAP1=P10.12)” in the dropdown box and close window with “OK”-button
• Click “HW Protect”-button and in the popup-windows “Start”-button afterwards. Be shure that no areas were selected for protectin before accepting the following message of IMT!
• After the process finished Memtool can be closed
In the “Das Device Scanner” the controller should be listed as “XE166/XC2000-Familiy” from now on and can be flashed via Memtool with Target Configration Profile for DAS
Hope this helps to get your Hardware connected?!
Not applicable
Sep 03, 2014
05:40 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 03, 2014
05:40 AM
Thanks for your help. Finally the connection to the XC2723X Microcontroller is working and the programming of the BMI was successful.
In order to connect with memtool it is also important to set the Hardware config pins to ASC Bootloader:
TRST -> High
P10.12 -> High
P2.9 -> X (High or low)
PORST -> High
In order to connect with memtool it is also important to set the Hardware config pins to ASC Bootloader:
TRST -> High
P10.12 -> High
P2.9 -> X (High or low)
PORST -> High
Sep 03, 2014
06:17 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 03, 2014
06:17 AM
Thanks for the hint on the hardware configuration.
> this should be done via restistors (otherwise control of the pins either by Controller or by Wiggler would not be possible)
> this should be done via restistors (otherwise control of the pins either by Controller or by Wiggler would not be possible)