Welcome to the Infineon Developer Community

Hi,

I  want to configure my UART module  

TX should happen with 10US that i have configured with GPT ,

RX should happen with Interrupt based. 

same when i tested RX got struck in IfxStm_isDeadLine(inline) function.

I want to know why it is getting strucked

Hello Team,
We are planning to use the MOSFET IPTG039N15NM5 for one of our applications.
We are using a Photovoltaic MOSFET Driver VOM1271T to drive the MOSFET.
Hence the gate to source voltage will be 8.4V.
Attached is the snippet from the schematic of the same.

Our requirements are.

• Maximum drain voltage = 48V (so the MOSFET shall have a VDS > 60V)
• Low RDSon =  as low as possible
• Gate Capacitance = as low as possible (since the output current of the VOM1271T is only 15uA, a high gate capacitance will result in high turn on time).
• Low OFF state capacitance =  The drain to source off state capacitance shall be very low else we will get high frequency signals at the output even if the MOSFET is OFF.
• Continuous Drain Current = >150A (The continuous drain current of the MOSFET is marked as 190A in the datasheet.)
  So can you please confirm whether a single MOSFET is enough to carry 150A of current.
  On our system, the 150A current may last for 5-10 Seconds.
  The continuous current will be 90A for all other time.
  What are the precautions we need to take for such a high current.
  Please confirm whether a single MOSFET is able to carry this much current?.
  
  Looking for your reply.

I need to design 2 isolated supplies. For both, I am fed by a PFC front-end with a input voltage range 350V ~ 410V. My output shall be 28V. The 1st supply should deliver 200W and the 2nd supply should deliver 400W. I was first considering the LLC topology with ICE2HS01G-DS but after going into some reference material, found that EMI will be a problem later on due to the varying frequency of the converter. I therefore am considering a forward converter topology with an active clamp. I want to use the same topology for both designs in order to re-use circuitry and minimize risk. I came across the XDPP1100 digital power controller but what I would like to verify is whether the choice of topology and controller is in fact the optimum choice. I am not space constraint but my operating temperature will be at a maximum of 65 deg C, so efficiency is critical. I do not have forced air to cool down my design so I will have to rely on conduction cooling. Some inputs or advice will be greatly appreciated.

In the BGT60LTR11AIP shield XENSIV™ 60 GHz radar system platform application note, under SPI mode and motion detection algorithm, it states that a detection range of 14m is possible and that the firmware used to achieve this is the “Radar Advanced Motion Sensing with SPI” application available from the Radar Fusion GUI is used. However, I have tried downloading the radar fusion GUI and it is not clear how this algorithm works. I am trying to integrate the BGT60LTR11AIP into a product that will be mounted at 8m and currently i am only getting detection at around 4m so would like to see how this advanced motion detection range is possible. 

近日，我购买了一块KIT_AURIX_TC397_TFT板子，里面是官方默认的固件， 我看说明书里通过板子的Mini USB连接PC （Windows 10 )，就可以识别到板子，但是我用usb连接后，板子TFT屏幕正常点亮，只有D106 (V_UC)、D104 （SS2）灯亮和P13中的一颗灯在闪烁，但在PC设备管理器里面找不到Infineon JDS DAS COM和Infineon JDS DAS Debug，安装DAS软件也无法识别，这种情况应该怎么处理?

Hello,

I would like to design a synchronous buck converter using XMC4200. I would like to implement a soft-start. How can I do that? Is there any documentation to help?

Thanks.

Jedison

Hi,

I have some question regarding the BGT60LTR11AIP (+Shield + MCU7 radar baseboard):

When using Radar Fusion GUI_1.5.4 to detect sensor BGR60LTR11AIP, the LEDs on the sensor and development board can light up normally and change colors when objects are moving. However, the device cannot be found in the software Radar Fusion GUI_1.5.4. I want to manually update the firmware, but there is no response from the device or firmware version drop-down box in the Decision ->Flash Firmware dialog box. I have reviewed the solutions on the forum regarding BGR60LTR11AIP No Decided, but I have not found where to download the "Radar BGT60LTR11AIP" software and the file "InitializeBGTxxx. bat", and where should I download this file.

Radar Fusion Gui Version: v3.5.4

Thanks for your time,

Regards,

xiao

Hi all,

We would like to measure the phase margin at EVAL_TDA38740_3.3VOUT.

Could you please check if the attached method is correct?

If it is not correct, please tell me how to measure it.

If you have the phase margin of EVAL_TDA38740_3.3VOUT, please provide it for us.

Best regards,
MS

Hi

I want to us HID at cyw20706.

https://community.infineon.com/t5/ModusToolbox/I-can-t-find-HID-example-in-ModusTool-box/m-p/399265#M2521

Based on the above question, an example exists for cyw20835.

I wonder if this example can be applied to cyw20706.

I was told at the time that it was not possible, is it the same now?


Thank you.

Regards,

DevRyan.

DPLL的RAM2C区域用来保存TRIGGER信号的特征，相应的内存寄存器为Memory DPLL_ADT_T[x],但是直接使用这个寄存器在ADS中无法识别此寄存器，求助。